Pada tutorial ini desktop yang saya gunakan adalah desktop KDE, wvdial dan nano sudah terinstall, apabila belum terinstall maka install dulu lewat YAST atau Zypper. Modem Smartfren Huawei EC 1260-2 ini di dukung pada OpenSuse 11.4 tidak perlu install driver lagi. Berikut langkah-langkahnya:
- Colokin modemnya
- Buka terminal
- sudo wvdialconf
- Masukin password root
patenpisan@linux-qnmb:~> sudo wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3 S4 S5 S6 S7 S8
Modem Port Scan<*1>: S9 S10 S11 S12 S13 S14 S15 S16
Modem Port Scan<*1>: S17 S18 S19 S20 S21 S22 S23 S24
Modem Port Scan<*1>: S25 S26 S27 S28 S29 S30 S31
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: +GMI: HUAWEI TECHNOLOGIES CO., LTD
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB3<*1>: ATQ0 V1 E1 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB3<*1>: Modem Identifier: ATI -- Manufacturer: +GMI: HUAWEI TECHNOLOGIES CO., LTD
ttyUSB3<*1>: Speed 9600: AT -- OK
ttyUSB3<*1>: Max speed is 9600; that should be safe.
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
ttyUSB3<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
5. Edit settingan wvdial.conf anda sesuai dengan operator yang anda gunakan
sudo nano /etc/wvdial.conf
Kalau udah selesai simpan dengan perintah Ctrl + O, untuk keluar Ctrl + X
6. Berikut settingan wvdial.conf dengan operator mobi (smartfren)
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem = /dev/ttyUSB0
Phone = #777
Idle Seconds = 300
Modem Type = USB Modem
Stupid Mode = 1
Compuserve = 0
Baud = 460800
Auto DNS = 1
Dial Command = ATDT
Ask Password = 0
ISDN = 0
Password = m8
Username = m8
7. Untuk menyambungkan pake perintah sudo wvdial
patenpisan@linux-qnmb:~> sudo wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Idle Seconds = 300, disabling automatic reconnect.
--> Sending: ATDT#777
--> Waiting for carrier.
ATDT#777
CONNECT
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Thu Sep 1 14:54:42 2011
--> Pid of pppd: 2177
--> Using interface ppp0
--> local IP address 10.184.96.175
--> remote IP address 10.17.95.3
--> primary DNS address 10.17.3.244
--> secondary DNS address 10.17.3.252
--> Script /etc/ppp/ip-up run successful
--> Default route Ok.
--> Nameserver (DNS) Ok.
--> Connected... Press Ctrl-C to disconnect
8. Selama internetan terminal jangan ditutup, apabila pengen disconnect tekan Ctrl - C
This is dummy text. It is not meant to be read. Accordingly, it is difficult to figure out when to end it. But then, this is dummy text. It is not meant to be read. Period.